Register    |    Sign In   |   
electronic MUSICIAN
» » »

Using Octave Dividers Lebanon OR

Most amp sims include octave dividers. I've successfully used octave dividers on bass with IK MultimediaAmpliTube 2, Waves GTR Solo (Figure1) and GTR3, Native Instruments GuitarRig 3 (Figure 2), Line 6 POD Farm,and Peavey ReValver Mk III. There's not a lot of difference among these particular effects; they all do the job.You can also use the other available modules to condition the bass signal.

Quadrant Systems
(503) 234-5558
P.O. Box 14833
Portland, OR
Services
Audio / Video, Home Automation / Systems Integration / Home Networking, Home Theater, Lighting Control, Security / Access Control / Surveillance / Gate Access
Brands
Runco, Denon, LG, Samsung, Elan, AMX, Genelec, Triad, Velodyne, Lutron, DSC, Niles
Certifications
One or more employees at this company have achieved CEDIA Professional Certification status:- Peter Bledsoe, CEDIA Certified Professional Installer I- Ben Kelsey, CEDIA Certified Professional Installer I- Jamey Nedelisky, CEDIA Certified Professional Installer I- Jeff Priester, CEDIA Certified Professional EST II

Stereotypes Audio
(503) 280-0910
1401 SE Morrison Street # 115
Portland, OR
 
The Audio Gallery
(503) 699-8888
16318 SW Bryant Road
Lake Oswego, OR
 
Cinematouch
(503) 675-1791
402 N State Street Cinematouch
Lake Oswego, OR
 
Video Only
(503) 283-3534
1900 N. Hayden Island Drive
Portland, OR
 
Room Service Home Technologies
(503) 598-7380
10120 SW Nimbus AvenueSte. C-1
Portland, OR
Services
Audio / Video, Home Automation / Systems Integration / Home Networking, Home Theater, Lighting Control, Security / Access Control / Surveillance / Gate Access
Brands
Crestron, Niles, Lutron, Kaleidescape, PHC, Request, Paradigm, Triad, Sony, EPSON, Samsung, Anthem, Integra, Audio Control, Pakedge, DSC, Sequel, SnapA/V, Panasonic, Universal Remote, Stewart, Screen Innovations, and Salamander.
Certifications
One or more employees at this company have achieved CEDIA Professional Certification status:- Erik Carter, CEDIA Certified Professional EST II- Roger Evashenko, CEDIA Certified Professional EST II

Best Buy
(541) 736-1127
3300 GATEWAY ST
Springfield, OR
 
Sound Man
(541) 882-6632
5220 S 6th Street
Klamath Falls, OR
 
Good Vibrations
(541) 673-4764
957 NE Stephens Street
Roseburg, OR
 
Bradfords Hi-Fidelity
(541) 344-8287
942 Olive St
Eugene, OR
 

Using Octave Dividers

Octave dividers aren’t just for guitarplayers: They also rock for bass,whether you’re getting mega-low sounds from the lower strings, or playing high up on the neck for very cool 8-string bass effects. It’s easy to do octave division with amp simsand DAWs, but there are some definite tricks involved.


Split Your Signal

As when adding many other types ofeffects on bass, it’s best to create asecond track in parallel with the main bass sound, and dedicate thesecond track to the octave divider.This lets you mix in the precise amount of octave sound, but more importantly, you may need to conditionthe bass signal to optimize it foroctave division.

Choose Your Divider

Most amp sims include octave dividers. I’ve successfully used octave dividers on bass with IK MultimediaAmpliTube 2, Waves GTR Solo (Figure1) and GTR3, Native Instruments GuitarRig 3 (Figure 2), Line 6 POD Farm,and Peavey ReValver Mk III. There’snot a lot of difference among theseparticular effects; they all do the job.You can also use the other availablemodules to condition the bass signal.

Pre-Octave Processing

Two main problems can interfere with proper triggering: an inconsistent input signal level, and triggering on aharmonic rather than the fundamental(which causes an “octavehopping”effect, where the signal jumps back and forth between thefundamental and octave).

A compressor can solve the consistencyproblem. Set it for a moderate amount of compression (e.g., 4:1 ratio,with a fairly high threshold). Make surethe compressed sound doesn’t have a“pop” at the beginning, and the sustainis smooth. Then if needed, patchin an EQ to take off some of thehighs—the object is to emphasize the fundamental. This may requirecompromise; too much filtering willreduce the level from the higherstrings to where they might not beable to trigger the octave divider(as well as change the tone),where as not filtering enough maycause octave-hopping on thelower strings.

What works best for me is cuttinghighs and boosting the low bass abit. If the EQ curve isn’t sharpenough, you may get better resultsby patching two EQs in series. I’vealso found that with Guitar Rig 3,using the Pro Filter module withmode set to LPF (lowpass) and slopeto 100% four-pole provides outstandingconditioning, especially whenpreceded by the Tube Compressor.

The Final Touch

Playing technique also matters.Popping and snapping might confusethe octave divider, as can the transients that occur from playingwith a pick. Playing with your fingersor thumb gives the best results, but don’t be afraid to experiment;for example, if you do “snap”the string, the sound might maskthe divided sound anyway, so itwon’t matter. Also, remember thatoctave dividers are monophonic, somake sure only one string vibrates at a time.

Once you have your signal chain tweaked, adjust the parallel, octave divided signal for the right balance with the main bass signal. You’llprobably find yourself playing anoctave higher than normal, becausethe octave divider will supply thelow ...

Click here to read the rest of the article from EQ Magazine

Discover Emusician